DIY Basement Drywall Installation Guide

Option 1 to Install Basement Drywall

Hanging basement drywall is probably the hardest part of ending up a basement, but it can likewise be one of the most satisfying since you are only one action away from having a space basement room that in fact looks like a space.

Many property owners with an incomplete basement wish to finish without professional assistance, which can be finished with the right knowledge and devices. If you have neither, you’ll need to purchase or borrow the devices. The know-how comes a bit a lot more conveniently. Adhere to these actions to drywall your basement.

Step 1 – Providing Wall Framing

Typically, unfinished basements have bare concrete or cinder block wall surfaces. In either case, you will certainly require mounted wall surfaces into which you will be able to affix drywall. Your type will need lower and also leading plates, as well as upright studs that are 8-feet high and are spaced at 16-inch periods.

This spacing is created to accommodate the attachment of drywall sheets that are commonly 4-feet wide and also 8-feet tall. With this spacing, the side edges of every drywall end at the center of a stud and also the leading and bottom sides finish at the facility of a plate, which is the best area for these sheets to end. It permits each drywall sheet to be tacked onto the stud with drywall screws.

Step 2 – Acquiring Your Drywall

Drywall can be found in common 4×8-foot sheets, however the thickness of the sheets differs. For application in a domestic building and construction job such as ending up a basement, you need to make use of sheets with a density of 3/8-inch. Stack your sheets near the space where you will hang them. If you pile them in the room where you will certainly be hanging them, you’ll find yourself needing to relocate them, a job that you will certainly not enjoy.

Step 3 – Attaching Your Drywall Sheets

Begin connecting your sheets at one corner of the room. Use your power drill to insert drywall screws 16-inches apart on studs and also plates. Continue this exact same procedure till you reach the end of the wall surface. The last sheet is not likely to end at the specific corner of the space and will certainly should be cut to ensure that it finishes at an edge stud where it can be affixed. Finish attaching drywall sheets on other walls the same way.

Step 4 – Using Tape as well as Mud

Cover each joint in between the sheets with seam tape and mud. Using a joint knife, first apply a strip of mud down the joint. This mud will certainly both fill up the joint as well as function as an adhesive to connect the seams to the drywall.

Apply the joint tape over the mud, after that use one more layer of mud over the seam tape to smooth its sides. At areas beyond the tape strips put on screws have been placed into the drywall, you’ll discover a shallow dent which should be loaded with drywall mud. When the mud is dry, smooth the rough sides with sandpaper as well as your wall surfaces will await their layer of paint guide. – source: DIYNetwork

Option 2

Transfer Outlet Cutouts

When setting up slim paneling, put up drywall as a substratum for the paneling to connect to.
For transferring electrical outlet cutouts into the drywall, use lipstick or an additional noting device to leave a perception on the drywall (Picture 1).

Trace around the electrical outlet box (Photo 2), established the drywall in position as well as press it up against packages.

Install Spacers

Use spacers so the drywall does not touch the concrete flooring as well as perhaps pick up any moisture that might be present in the concrete. Permit a 1/2″ space between the drywall and the flooring.

Connect the Drywall

Utilize a drywall saw to reduce outlet markings outside the lines on drywall (Photo 1).

Safeguard the drywall to the studs (Picture 2). Countersink the screws, ensuring to only dimple the paper. Beware not to break through the paper or this will compromise the architectural honesty of the drywall.

Make reference lines on the drywall (Picture 3) as a stud recommendation when screwing in the drywall.

For home windows, cover the window and also come back to cut it out after the drywall is safe and secure (Picture 4).

Leave a Comment